Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Antelope
Electric gate repair in Antelope usually means one of two things: a gate that won’t open, or a gate that won’t close. The fix typically runs between $180 and $550 depending on the part, and we can diagnose most Antelope gate failures on a single visit. Call (279) 266-8501 and you’ll reach a live person who can schedule a technician for your side of town, whether you’re near Antelope Road or off Walerga.
We know Antelope’s gate problems because we see them every week. The 1980s-era ornamental iron in the older neighborhoods behaves differently from the steel tube gates in the newer 2000s subdivisions off Elverta Road. Heat-warped tracks, seized hinges, boards that stop reading the keypad. None of it surprises us anymore, which means we arrive with the right parts and a plan already half-formed.
Before we touch anything, you get a written price. You agree to it, then we work. No invoice inflated after the fact, no “while we were in there” additions. Just the number we shook on, in writing.
Key Takeaways:
- Most Antelope electric gate repairs run $180 – $550 and are diagnosed in one visit.
- We work with HOA boards and management companies on pre-approved styles and finishes.
- Every visit includes a written price before work starts, shoe covers, drop cloths, and a cleanup photo.
- A live person answers our phone 24/7, including holidays.
Why Latch and Post Gate Repair Sacramento Is Antelope’s Preferred Electric Gate Repair Company
We’re part of the Cedarwell family of independently owned and operated gate specialists, and our Electric Gate Repair team has handled Antelope HOAs, single-family gates, and community entrances since our founding in 2009. Antelope homeowners call us because we understand something most gate companies don’t: this town runs on HOAs. The ornamental black iron gate you see on one street is the same pre-approved style on the next street over, and the board notices when a repair changes the look.
That’s why we don’t just fix the gate. We ask about architectural review. We photograph the finish. We match the exact pre-approved black or bronze tone before reinstalling a hinge or operator arm. For Antelope’s HOA communities, that’s the difference between a repair that gets signed off and a repair that generates a letter from the management company.
Our technicians are background-checked and uniformed, factory-trained on LiftMaster, FAAC, BFT, and Linear. They follow the Cedarwell C.A.R.E. values on every visit: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work. You’ll see shoe covers before we step inside, drop cloths on the floor, and a photo of the clean-up before we leave.
Every job is covered by the 365-Day Done Right Promise. If the repair isn’t right, we make it right. No argument, no fine print.
Styles & brands we work with
Gate Access Control in Antelope
Gate access control in Antelope means the system that decides who gets in: keypads, remotes, vehicle loop detectors, telephone entry, and the control board that ties them together. When your community entrance gate off Antelope Road stops reading keypad codes, or your driveway gate ignores the remote, you need a technician who can trace signal, not just swap batteries. Our access control work in Antelope typically runs $150 – $350 for keypad and receiver fixes, and $250 – $650 for control board replacement, with the exact number written down before we start.
Antelope’s HOA communities add a layer most cities don’t have. If a safety photocell fails at a community entrance, the board may need to review and approve the replacement part before work proceeds. We prepare a written quote with the exact part number and finish description so the management company can move the approval along quickly. For homeowners on narrow lots where swing gates clear the driveway by inches, a misaligned loop detector is usually the culprit when the gate opens for cars leaving but not arriving.
Keypad and Remote Entry Repairs
A keypad that beeps but won’t trigger the operator usually has a failed relay on the control board, not a battery issue. We bench-test the board, replace the relay, and re-sync your remotes on site. Most Antelope keypad and remote repairs finish same-visit with parts we carry in the truck.
Community Entry Systems and Loop Detectors
For Antelope’s gated communities, a dead loop detector means the exit works but the entrance won’t open for resident cars. We test the loop, adjust sensitivity, and where the saw-cut has been damaged by years of Sacramento Valley heat and dry soil shift, we recut and reseal it. The management company gets a written report they can file for the HOA’s records.
Commercial Gate Operator in Antelope
A commercial gate operator in Antelope is the motor and drive system that moves a community entrance gate, a church parking gate, or a small business gate off Antelope Road. When the operator over-torques or the arm binds because the gate itself is sagging from years of dry soil and hot summers, the motor fails early. We replace or rebuild operators for Antelope commercial and HOA clients at $450 – $1,200 depending on the operator size and whether the gate’s hinge pins need correction before the motor goes back on.
The timing matters to HOAs. A failed operator at a community entrance means every resident uses the visitor lane, and the board wants it fixed fast but also wants it done to the pre-approved standard. We coordinate with the management company: written quote with the operator make and model, finish-matched hardware, and a service window that works for the board’s approval process. In an HOA off Walerga Road, we repaired a LiftMaster LA400 swing gate operator that was over-torquing after years of Sacramento Valley heat. The original ornamental iron gate had seized hinge pins and no grease fittings, so we drilled and tapped zerks, corrected the sag at the hinge post, and worked with the management company to match the pre-approved black finish before reinstalling the operator.
Operator Rebuilds vs. Replacement
Not every dead operator needs to be replaced. If the motor hums but the gate won’t move, the issue is often the drive gear or the limit switch, and a rebuild with factory parts is cheaper and faster. We tell you which road makes sense for your gate and give you the number either way.
Safety Sensor and Photocell Repair
A gate that stops halfway and reverses is usually a failing safety photocell or a misaligned sensor edge. We replace sensors and realign edges on Antelope community gates, then test the operator’s obstruction detection before we call the job done. On HOA gates, we supply the part spec so the board’s architectural review has what it needs.
Trusted Brands We Service in Antelope
We’re factory-trained on the brands families and HOAs actually run in Antelope: LiftMaster, FAAC, BFT, and Linear are the most common we see on local driveway and community gates. We stock common control boards, remotes, and safety sensors for these brands, which means faster turnaround for Antelope customers and fewer second visits. If your operator came with the house in a 1990s subdivision off Walerga Road, it’s likely a LiftMaster or FAAC. If a contractor retrofitted it in the 2010s, probably a Linear or BFT. We carry parts for all of them on the truck.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Antelope Homes
- Hinge sag on lightweight aluminum and steel tube gates. Tract builders in Antelope’s 1980s – 2000s starter-home subdivisions installed gates that were never intended to carry decades of Sacramento heat. The hinges sag, the gate drags on the concrete, and the operator’s gears bind and strip.
- Seized hinge pins with no grease fittings. In the older neighborhoods east of Walerga Road, original 1980s ornamental iron gates have no accessible grease fittings. We drill and tap new zerks as a standard fix, which no one tells you on a generic gate repair website.
- Warped tracks from thermal expansion. Antelope’s hot, dry summers and occasional winter frost expand and contract the metal, which slowly bends the track. A sliding gate starts grinding, and the rack and pinion chew each other.
- Keypad and control board failures from repeated thermal cycling. Board solder joints crack after enough years of 100° days and 32° nights, which is why your keypad beeps but the gate won’t respond. We reflow or replace the board and re-sync everything before leaving.
Pricing for Electric Gate Repair in Antelope, CA
A typical electric gate repair in Antelope runs $180 – $550 for common failures: keypad replacement, safety sensor swap, hinge correction, or limit switch adjustment. Control board replacement lands $250 – $650. Full operator replacement on a driveway swing gate runs $450 – $900, and a community entrance operator $700 – $1,200. The main cost drivers in Antelope are HOA-mandated finish matching and the extra labor of correcting years of hinge sag before a new operator goes on. We give you a written price before any work starts, every single visit, and that number does not change unless we find something new and you approve the new number in writing. Call (279) 266-8501 for a free estimate.
We Also Serve Cities Near Antelope
Our electric gate repair in Antelope also reaches homeowners in Citrus Heights, Carmichael, Fair Oaks, and Roseville. If you live just over the line, call us and we’ll confirm we cover your street. We schedule by neighborhood, not by zip-code gimmicks.
Serving Antelope, CA - Our Local Coverage Area
We’re based in the Antelope area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Antelope
You can, but you may not get it approved. Antelope HOAs often require that any visible gate hardware match the pre-approved style and finish, and a DIY part swap with a different hinge or a silver bracket where black iron was approved will land you a letter from the management company. We match the finish and supply part specs for the board’s review, which clears the repair faster. Call (279) 266-8501 and we’ll tell you exactly what part we’d use and what the board needs to sign off.
It’s almost always a failing safety photocell or a misaligned safety edge. When the operator’s obstruction detection reads a false signal, it reverses direction and stops the gate mid-cycle. In Antelope’s summer heat, photocell alignment drifts as the metal housing expands. We replace the sensor and re-test the obstruction detection until the gate cycles cleanly.
No. If the motor hums but the gate doesn’t move, the drive gear or limit switch is usually the failure point, and a rebuild with factory parts costs less than full replacement. We’ll tell you which failure you have and quote both paths honestly, with the written number in your hand before you decide.
You should check your CC&Rs first. Many Antelope HOAs review any visible change to the gate, including a solar panel mounted on the post or a new operator arm, because it changes the gate’s appearance from the street. We’ll tell you what’s visible and what’s hidden in the proposal so you can take an accurate description to the board.
Not necessarily. Grinding usually means the gate has dropped and the chain or rack is misaligned with the drive sprocket. We correct the gate’s level, adjust the track and rollers, and repitch the rack. If the rack teeth are actually worn from years of dragging, we replace the rack section and not the whole operator. Call (279) 266-8501 for an exact quote.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Sacramento, serving Antelope since 2009.